@jsecord
-
Steve Bauman and
Karen Wade are now friends 8 years ago -
Becky Jones and
Karen Wade are now friends 8 years ago -
Becky Jones and
John Secord are now friends 8 years ago
-
Ed Pulliam replied to the topic Window and windshield 200D in the forum Airframe – Meyers 200 8 years ago
John, on another matter-can you take a picture of the vent and post you mentioned on the hat shelf?
Much obliged.
-
John Lyon replied to the topic Window and windshield 200D in the forum Airframe – Meyers 200 8 years, 1 month ago
Back in the Olden Days (1993), Don Petty sent 200D windows, for making molds, to Aircraft Windshields, 10871 Kyle Street, Los Alamitos CA 90720, Tel 562-430-8108. It was then, and is now, run by Judy Gallo, and has been in business for 50 years. That was a long time ago, and who knows if they can do anything now, but it is worth a try if Cee…[Read more]
-
Reb Stimson's profile was updated 8 years, 1 month ago
-
John Lyon replied to the topic hydraulic pressure in the forum Hydraulic System – Meyers 200 8 years, 1 month ago
The whole spool valve was a vendor part, custom manufactured for Meyers. I would take the spring to a large dealer and see if they can match it. Century Spring Corp?
-
Thomas Kube replied to the topic Introduction and advice needed in the forum General- Meyers 200 8 years, 1 month ago
Thank you for the information. The crack has been drilled and I am watching it.
I am in the progress of talking to some specialists for having the the plane repainted.Will keep you informed.
Thomas
-
Jamon Pruitt replied to the topic hydraulic pressure in the forum Hydraulic System – Meyers 200 8 years, 1 month ago
Make sure your pump is good also could be loss of pressure from worn seals in the pump the spring will usually compress and coil bind with lots of shims “washers” and pressure will go up , probably to high ouch!
-
Ed Pulliam replied to the topic Introduction and advice needed in the forum General- Meyers 200 8 years, 1 month ago
Thomas, I replaced all except windshield in 2012 and also used Cee Bailey’s. We have heard they have been hard to get of late, but Mark is right, that’s the place to start.
Assume the crack has been stop-drilled for now?
-
Mark Jensen started the topic hydraulic pressure in the forum Hydraulic System – Meyers 200 8 years, 1 month ago
Does anyone know of a source for the spring that regulates hydraulic pressure(part number: D65B046-5)?
This spring applies pressure to a small plastic ball and mine has weakened and been shimmed with washers as much as possible. It now needs to be replaced. My mechanic was able to get the plastic ball from Joan Diver. It had to be replaced as…[Read more] -
Mark Jensen replied to the topic Introduction and advice needed in the forum General- Meyers 200 8 years, 1 month ago
Hi Thomas,
I replaced all the glass on my 200 in 2001. Last month, I replaced the small vent window. The glass is available from Cee Baileys Aircraft Plastics. The web site is http://www.ceebaileys.com. They are currently listing the rear window for $390.00. Hope that helps.
Mark Jensen
-
Becky Jones and
Dane Pruitt are now friends 8 years, 1 month ago -
Reb Stimson and
John Lyon are now friends 8 years, 1 month ago
-
Dan McLeod and
Hugh Mattern are now friends 8 years, 1 month ago
-
Steve Bauman and
Steve Windh are now friends 8 years, 1 month ago
-
Steve Bauman and
Steve Freeman are now friends 8 years, 1 month ago
-
Jay McLeod and
-
Jay McLeod changed their profile picture 8 years, 1 month ago
-
Thomas Kube replied to the topic Nose strut, Positive stop in the forum Landing Gear – Meyers 200 8 years, 1 month ago
Hi, I have it installed as my plane is SN 368, the first one not affected.
It looks exactly like the drawing.I have a front view picture where you see it and can make details by mid September.
Please send me an email to thomas_kube@me.com as I cannot upload from my iPad.Cheers,
Thomas
- Load More
