-
Ross Warner replied to the topic landing gear placards/decals in the forum Landing Gear – Meyers 200 3 years, 9 months ago
Hi Mark. I have most all the decals required for the 200 including what you need. I’m bringing samples to the fly-in but could mail anything you need. Call me at 269-369-1052 Ross Warner
-
Webmaster and Garry Elghammer are now friends 3 years, 9 months ago
-
Webmaster and TC Gromer are now friends 3 years, 9 months ago
-
Tom Thibodeau and TC Gromer are now friends 3 years, 9 months ago
-
Tom Thibodeau and Ken Rizer are now friends 3 years, 9 months ago
-
Tom Thibodeau and Ed Pulliam are now friends 3 years, 9 months ago
-
Tom Thibodeau replied to the topic Assets Of Meyers 200 Business in the forum General 3 years, 9 months ago
Global made a presentation at last year’s fly-in in FL. They hired a market specialist to actively search for a buyer. Their plan was to keep all of the assets (TC, fixtures, parts, M400, and 2918T) together as a package sale. If they were not able to sell the entire package, Nin George said they would contact our Association prior to d…[Read more]
-
Tom Thibodeau and Hans are now friends 3 years, 9 months ago
-
Tom Thibodeau replied to the topic landing gear placards/decals in the forum Landing Gear – Meyers 200 3 years, 10 months ago
Mark,
I believe I have one in my stash of parts. I’ll check next trip to my hangar in a week or so. Do you need them for the mains as well? I’ll let you know what I find …
Have you asked Joan Diver about them?
r, Tom Thibodeau
757.870.2474 -
Tom Thibodeau replied to the topic tail wheel boots? in the forum Airframe – Meyers OTW 3 years, 10 months ago
DIck,
Did you get your boot?
R, Tom
-
Tom Thibodeau replied to the topic Noise certificate in the forum Meyers 200 3 years, 10 months ago
Thomas,
I’m not familiar with a noise certificate being issued for the M200, but Marv Rogge had to complete noise testing when he installed the IO-550 with a 2 bladed prop on his aircraft. He or Steve Bauman may be able to answer if a “stock” certificate exists.
R, Tom
-
Tom Thibodeau replied to the topic Conversation in the forum Meyers 200 3 years, 10 months ago
Mark,
Sounds like your elevator trim is now correctly rigged. It should require 4 half turns (2 full turns) from full nose down to set at take-off position.
VR, Tom
-
Webmaster and Andy Nixon are now friends 3 years, 10 months ago
-
Tom Thibodeau and Hugh Mattern are now friends 3 years, 11 months ago
-
Webmaster and Hugh Mattern are now friends 3 years, 11 months ago
-
Webmaster and Jim Abbott are now friends 4 years ago
-
Tom Thibodeau replied to the topic Conversation in the forum Meyers 200 4 years ago
Hi Ed,
I typically fly a little slower than most, but 100 mph on DW, 90 mph on base, and crossing the fence (just short of threshold at 85 mph works fine for me. I carry a little bit of power into the flare, and roll it off as the nose comes up. You don’t want to try to flare at 80 mph without any throttle, as it will sink through to a c…[Read more]
-
Tom Thibodeau replied to the topic 4 Point Harnesses – Front Seats? in the forum Interiors – Meyers 200 4 years, 1 month ago
Does anyone have an approved 337 for a 4-point harness?
R, Tom
-
Tom Thibodeau replied to the topic Actuator Seals in the forum Hydraulic System – Meyers 200 4 years, 3 months ago
Robert,
I do have the part numbers and quantities required and multiple extra seals since I was sent a duplicate order. However, I am currently on an extended work trip and do not have access to my data or parts at this time. If you are able to wait until mid-March, I will send you a complete set of seals (or just the part numbers) at no cost.…[Read more]
-
Tom Thibodeau and Ashley Wade are now friends 4 years, 3 months ago
- Load More