-
Tommie Barg and
Michael Barg are now friends 3 years, 1 month ago
-
Tommie Barg's profile was updated 3 years, 1 month ago
-
Becky Jones and
Tommie Barg are now friends 3 years, 1 month ago
-
Becky Jones and
-
Ed Pulliam replied to the topic Propeller Governor bad in the forum Engine – Meyers 200 3 years, 1 month ago
Even bigger fake on WX. Going to be 84’F in NC on Thursday. Trees and plants are very confused…
My gear door issue was satisfactorily resolved and they were also able to re-weld the wing walk support on the wing inside of the flap. I dare say a lot of our fleet has busted wing walk supports. I don’t think it is an AW issue, but more of a…[Read more]
-
Ed Pulliam replied to the topic Propeller Governor bad in the forum Engine – Meyers 200 3 years, 1 month ago
Even bigger fake on WX. Going to be 84’F in NC on Thursday. Tress and plants ae very confused.
My gear door issue was satisfactorily resolved and they were also able to re-weld the wind walk support on the wing inside of the flap. I dare say a lot of our fleet has busted wing walk supports. I don’t think it is an AW issue, but more of a PITA…[Read more]
-
Ed Pulliam replied to the topic Spare airframe in the forum Airframe – Meyers 200 3 years, 1 month ago
Bailey-a follow up to Donn’s note. Any pics and specs to share??
Best
Ed
196M -
Ed Pulliam replied to the topic Propeller Governor bad in the forum Engine – Meyers 200 3 years, 1 month ago
Excellent!! Very glad to hear. I am dealing with a gear door issue that hopefully is resolved tomorrow. 73’F in NC today. A big fake…
-
Ed Pulliam replied to the topic Propeller Governor bad in the forum Engine – Meyers 200 3 years, 1 month ago
Excellent!! Very glad to hear. I am dealing with a gear door issue that hopefully is resolved tomorrow. 73’F in NC today. A big fake…
-
Thomas Kube replied to the topic Propeller Governor bad in the forum Engine – Meyers 200 3 years, 1 month ago
Update: some tweaking of the idle mixture and the engine runs fine. Take off fuel flow ist 28,3 gal/h resulting in good temperatures and performance „as expected“ by us. Annual done and the weather is also improving.
Keep on flying them birds!
Thomas
-
Hugh Mattern and
John Lyon are now friends 3 years, 1 month ago
-
Hugh Mattern and
Bruce Mayes are now friends 3 years, 1 month ago
-
Hugh Mattern and
nelson harding are now friends 3 years, 1 month ago
-
Karen Wade wrote a new post 3 years, 1 month ago
-
Karen Wade wrote a new post 3 years, 1 month ago
-
Ed Pulliam replied to the topic Propeller Governor bad in the forum Engine – Meyers 200 3 years, 1 month ago
Thomas-My understanding is the fuel flow set-up is not overly complex for the person who understands it and has done it. Who in Germany have you used in the past? Wonder if you might find a YouTube that might show it?
One thing to make sure is that you adjust your fuel flow at wide open throttle at sea level to be 10% of your rated HP. So on…[Read more]
-
Thomas Kube replied to the topic Propeller Governor bad in the forum Engine – Meyers 200 3 years, 2 months ago
Update: had another cylinder overhauled and all rotocaps replaced. On Runup the fuelflow was well below spec. Had the fuel control unit overhauled here in Germany. Came back with factory settings. On run-up engine stalls below 1500 rpm. Need to setup the FCU according to SB. Did anybody venture this way before and has some knowledge to share?
I…[Read more] -
Donn Borden replied to the topic Spare airframe in the forum Airframe – Meyers 200 3 years, 2 months ago
Could you please be more specific as to what you are selling? Thank you.
-
Bailey Scheidel started the topic Spare airframe in the forum Airframe – Meyers 200 3 years, 3 months ago
Hello all.
A preface:
I would post this in classifieds but the method of doing so did not readily make itself available to me, therefore, into the airframe section we go!When we purchased n5507m about 3 years ago, we also received 2 spare airframes (both 200d’s) and various other parts worth of spares.
I believe the time has come to let one of…[Read more] -
STEPHEN MAYS's profile was updated 3 years, 3 months ago
- Load More
