-
Dean Siracusa replied to the topic Hydraulic aileron trim in the forum Airframe – Meyers 200 6 years, 4 months ago
You must not be getting my emails. Or, my emails are going into your spam folder. I shared all of their emails. My email address is my first and last name (as one word) at gmail.
-
Dean Siracusa replied to the topic Hydraulic aileron trim in the forum Airframe – Meyers 200 6 years, 4 months ago
The early Aero Commander 200D’s were essentially built by Meyers and have their original hydraulic aileron trim system. It’s complicated but Meyers built owners have solutions for maintaining them. Talk to Neslon Harding, Dave Smith or Ashley Wade about it. I’m sure they’ll have the answers you need.
-
Ed Pulliam replied to the topic Flaps in the forum Flight Controls – Meyers 200 6 years, 5 months ago
Chris-I have not had any issues with the bushings. My IA found a bolt installed backwards that was casing the flap to bind when it extended but it was easily rectified. Do the bushings look like off the shelf? Perhaps Dave Smith or Nelson Harding can respond.
Ed
-
Hinrik Hjaltason and
Steve Crawford are now friends 6 years, 6 months ago
-
Mark Jensen replied to the topic Pilot looking for information on 200d in the forum General- Meyers 200 6 years, 6 months ago
Hi Greg,
I did show my 200D to a interested person who is 6″6″ and I also fly with a neighbor who is 6″4″. neither had any problem with head or shoulder room. However, the first person had long legs which put his knees at the bottom of the yoke with the seat adjusted full back. I believe some owners have replaced their seats which, if coupled…[Read more]
-
Dan McLeod replied to the topic Avionics Upgrade in the forum Avionics – Meyers 200 6 years, 6 months ago
JPI 930 for 200D now is stc
-
Ed Pulliam replied to the topic 200 Air Oil Separator (AOS) FINALLY!!!!! in the forum Engine – Meyers 200 6 years, 6 months ago
Ashley-please post pics once the install is done.
Ed
-
Ed Pulliam replied to the topic Seats in the forum Meyers 200 6 years, 6 months ago
Sent you a PM Chris
-
greg grouleff replied to the topic 200 Air Oil Separator (AOS) FINALLY!!!!! in the forum Engine – Meyers 200 6 years, 6 months ago
Our 200 oil separator is a Garwin G200
-
Ashley Wade replied to the topic OTW DRAWINGS in the forum Airframe – Meyers OTW 6 years, 6 months ago
Hello Trevor,
I am a 200 guy and just going with Jim Jones to pick up my wife’s “new” OTW next week. Here is a current email address for Jim. Bet he can help you.
Ashley
-
Ashley Wade replied to the topic 200 Air Oil Separator (AOS) FINALLY!!!!! in the forum Engine – Meyers 200 6 years, 6 months ago
Hello Greg, “mist” I can handle. Drips from belly strobe and tail tie down I can’t. My usage is not bad at all and motor has only about 100 hours after full Lycon rebuild. She drooled before rebuild, unfortunately she drools after.
I have the originallittle Garwin AOS off of my wet vane vacuum already. Now with the AirWolf AOS in tandem like…[Read more]
-
greg grouleff replied to the topic 200 Air Oil Separator (AOS) FINALLY!!!!! in the forum Engine – Meyers 200 6 years, 6 months ago
I hate to be a spoil sport, I have an oil separator on our 200 and on other aircraft we own / have owned , but you will still have to clean off a fine mist of oil from the belly of your 200. Enjoy rubbing down the grand old dame, she gives us hours and hours of pleasure!
-
John Secord and
Tom Losey are now friends 6 years, 7 months ago
-
Steve Bauman and
Tom Losey are now friends 6 years, 7 months ago
-
John Secord and
Tom Losey are now friends 6 years, 7 months ago
-
Karen Wade and
Tom Losey are now friends 6 years, 7 months ago
-
Phil W. Hart and
Tom Losey are now friends 6 years, 7 months ago
-
Jim Jones and
Tom Losey are now friends 6 years, 7 months ago
-
Hinrik Hjaltason and
Tom Losey are now friends 6 years, 7 months ago
-
Becky Jones and
Tom Losey are now friends 6 years, 7 months ago
- Load More