@tparsons2919t
-
Gary Harber replied to the topic Yoke leather wrap in the forum Restoration / Rebuilding – Meyers 200 2 days, 12 hours ago
Actually, I think I found one that matches my yoke:
-
Gary Harber replied to the topic Yoke leather wrap in the forum Restoration / Rebuilding – Meyers 200 2 days, 12 hours ago
Let me know if you find anything that works and looks good
-
Steve Bauman replied to the topic Interior Lighting in the forum Interiors – Meyers 200 1 week, 2 days ago
Kevin
Please send me your EMAIL ADDRESS will send you pictures of N2960T when Susan OLIVER had the airplane
STEVE BAUMAN -
Steve Bauman replied to the topic Interior Lighting in the forum Interiors – Meyers 200 1 week, 2 days ago
Kevin
STEVE BAUMAN -here– N2989T–Your airplane was SUSAN OLIVERS’S airplane N2960T. It had the blue two tone paint scheme. Would you want to go back to the original “N” number?
Steve -
Ross Warner replied to the topic Interior Lighting in the forum Interiors – Meyers 200 2 months ago
I’ll forward a picture next time I’m at the hangar. pass on a cell number for a text photo. Ross
-
Ross Warner replied to the topic Interior Lighting in the forum Interiors – Meyers 200 2 months, 1 week ago
Keven, the glare shield is most definitely the overhang of the dashboard. The white lights would be mounted under to illuminate everything below in white light. They may have been removed by a previous owner? Hopes this helps. Ross
-
Ross Warner replied to the topic Interior Lighting in the forum Interiors – Meyers 200 2 months, 1 week ago
Hello Kevin. The second position for your panel light controls white light bulbs (four?) under the glare shield. Your bulbs may be burned out or a power wire detached. Ross
-
Ross Warner replied to the topic Oshkosh 2024 in the forum General- Meyers 200 2 months, 2 weeks ago
Ross and Son, Ross IV always attend and plan on early arrival on the 18th. We also have set up a Meyers group dinner at Wendt’s on the lake on Tuesday again, as you know. Should have several Meyers in attendance. Looking forward to seeing you all again. Ross
-
Joseph McDonald replied to the topic master cylinder for brakes in the forum Engine – Meyers 200 8 months, 2 weeks ago
From my notes last year, the Cleveland Brake Kit cylinders mentioned above use these for overhaul.
1Each
MS28775-XXX Part or AN6227B-X Part
011 / 6
014 / NA
008 / 3
111 / 9 -
Joseph McDonald replied to the topic master cylinder for brakes in the forum Engine – Meyers 200 8 months, 2 weeks ago
It will depend on if yours have been upgraded. Best to get part numbers off the existing ones. Mine had Gerdes A-110-27 which is a Cleveland 10-46.
Pages 3-12/13: https://www.aircraftsupply.com/pdf-files/Cleveland-Seal-Repair-Kits.pdf
Plane parts kit:…[Read more]
-
Mark Young wrote a new post 8 months, 3 weeks ago
The Annual, Late Summer Meyers Fly-in will happen this year at the Rough River Dam Resort in Kentucky (identifier: 2i3).
The fly-in will take place from September 17 through September 22.
Information can be
-
Mark Young wrote a new post 11 months, 2 weeks ago
Got a note from John Lyon pointing out an article in the most recent issue of Flying Magazine (Issue 942, October 2023).
I wouldn’t be appropriate to cross post the entire article, but I think it’s considered
-
Mark Young wrote a new post 1 year ago
I’m going to try to catch up on the name tags again at the fly-in.
If you’re coming to the fly-in and you lost or don’t have a nametag, send me an email to mark.young@gmail.com.
Heck, if you’d like a
-
Mark Young wrote a new post 1 year ago
Now just a couple of weeks out from the fly-in, we have a final update (no. 6) to the fly-in flyer. Looking forward to seeing a lot of you in Carson City, NV
Send email replies, questions, and comments to B
-
Mark Young wrote a new post 1 year ago
-
Mark Young replied to the topic *PAN PAN* Garmin GFC500 Available in Meyers 200! *PAN PAN* in the forum Avionics – Meyers 200 1 year, 1 month ago
I’ll post an update on my install. I had a set of other work done at the time, so I don’t recall the cost of the work done specifically for the autopilot.
I previous had a century 2000 with integrated electric trim, and century altitude pre-select.
While the system was functional, I considered it a bit mickey mouse. When tuned properly, it…[Read more]
-
Mark Young wrote a new post 1 year, 1 month ago
I probably should have considered this a lot sooner, but we’d like to get a sense for who will be attending the Fly-in this year in Carson City to facilitate some last minute planning that is going on. In this
-
Ross Warner started the topic golf outing during the Carson City fly in in the forum Meyers 200 1 year, 2 months ago
Looking forward to seeing our regular and new members in Carson City this September. My son and I plan on attending and bringing our sticks to play golf at the Eagle Valley golf course just east of our host airport. website eaglevalleygolfcourse.com. They have rental clubs if you don’t want to add extra weight to your Meyers. Just putting out…[Read more]
-
Mark Young wrote a new post 1 year, 2 months ago
Greetings all. Bruce Mayes and crew have another updated flyer for the 2023 fly-in.
2023 Flyin Notice No 4 (Click this link)
Once again, if you have any issues with flyer, please message me and I’ll
-
Joseph McDonald replied to the topic Spool Valve/Shuttle Valve in the forum Airframe – Meyers 200 1 year, 3 months ago
Just following up as I had the same question.
Nelson provided me these part numbers:
2 Each: MS28775-117
SFK or CR 711805Looking in the “(not) Illustrated Parts Manual” I have the below o-rings and seals listed for the standard AN/MS numbers for that valve:
1 – AN6227B-10 – O-Ring
2 – MS28775-117 – O-Ring
1 – AN6226-45 – Seal (this I believe is…[Read more] - Load More
