Latest News
2026 Meyers Aircraft Fly-in, September 9-13, Fredericksburg, TX (T82)
The Meyers group returns to the amazing Hangar Hotel at Fredericksburg, TX. Check out the flyer for details: MAOA...
Latest Forum Postings
-
Tony Parsons and
Steve Bauman are now friends 1 year, 9 months ago
-
Tom Thibodeau and
-
Tony Parsons replied to the topic High CHT #6 in the forum Engine – Meyers 200 1 year, 9 months ago
Hi Everyone! Newbie just now able to get on the site. I am having the same issue as Thomas. #6 is getting up to 430 on takeoff climb now that it is getting hot, 90 degrees. In cruise, all are under 380. I am at 400ft MSL, full rich, fuel flow is almost to redline, cowl flaps wide open. Injector is clear, AP says baffeling is fine. Bore…[Read more]
-
Tony Parsons and
Mark Young are now friends 1 year, 9 months ago
-
Dean Siracusa and
-
Tony Parsons and
Dan McLeod are now friends 1 year, 9 months ago -
Claudio replied to the topic Seats for 200D in the forum Interiors – Meyers 200 2 years, 2 months ago
Could try: Fiberglass Seats, Wingtips and Nose Bowls: Marvin Rogge, home: 702.655.9005, work: 702.631.9900
-
Tom Myers replied to the topic Seats for 200D in the forum Interiors – Meyers 200 2 years, 2 months ago
Hi All, I am a fairly new 200D owner, having purchased N2980T about 1.5 years ago. The reclining mechanism on my pilot seat will no longer stay in the most upright position (coincidentally after coming out of a months-long avionics/panel installation where the interior was removed). I pulled the seats out and suspect that the cylinder/spring…[Read more]
-
Roland Vandewouwer started the topic MAC 145 For Sale in the forum General 2 years, 3 months ago
MAC 145 Ser #222 Reg# N34379 is for SALE. Located at KCMA Southern California Roland Vandewouwer
-
John Secord started the topic Registration in the forum 2024 Winter Fly-In Spruce Creek FL 2 years, 3 months ago
Happy New Year!
Hey everyone, a last-minute fly-in has been pulled together here in Florida. I would love to see you all if possible. It was late throwing together due to my Home Owners board of directors needing to approve due to our airport being private. Have spoken to a number of you who said you are coming so please ensure to click on the…[Read more]
-
Joseph McDonald replied to the topic master cylinder for brakes in the forum Engine – Meyers 200 2 years, 3 months ago
From my notes last year, the Cleveland Brake Kit cylinders mentioned above use these for overhaul.
1Each
MS28775-XXX Part or AN6227B-X Part
011 / 6
014 / NA
008 / 3
111 / 9 -
Joseph McDonald replied to the topic master cylinder for brakes in the forum Engine – Meyers 200 2 years, 3 months ago
It will depend on if yours have been upgraded. Best to get part numbers off the existing ones. Mine had Gerdes A-110-27 which is a Cleveland 10-46.
Pages 3-12/13: https://www.aircraftsupply.com/pdf-files/Cleveland-Seal-Repair-Kits.pdf
Plane parts kit:…[Read more]
-
Mark Young wrote a new post 2 years, 3 months ago
The Annual, Late Summer Meyers Fly-in will happen this year at the Rough River Dam Resort in Kentucky (identifier: 2i3).
The fly-in will take place from September 17 through September 22.
Information can be
-
Jack Bart started the topic master cylinder for brakes in the forum Engine – Meyers 200 2 years, 3 months ago
I will try to rebuild mine but may need a new piston for master cylinder. Who is the maker of the master brake cylinder for the Meyers 200 D 1966 and who is the contact for parts for this item ?????????
-
Arne Vasenden started the topic Turbo Charger STC in the forum Engine – Meyers 200 2 years, 5 months ago
Any one know who has the Turbo Charger STC for the 550 engine?
-
Rocky Roquemore started the topic 200E #385 in the forum Meyers 200 2 years, 5 months ago
It is now at Roosevelt Memorial Airport GA.
RESTORATION is about 50% complete it will get a turbo 550 of about 340 hp and full garmin G3X suite.
Will be painted n original livery with N200EX reserved forbit. -
Mark Young wrote a new post 2 years, 6 months ago
Got a note from John Lyon pointing out an article in the most recent issue of Flying Magazine (Issue 942, October 2023).
I wouldn’t be appropriate to cross post the entire article, but I think it’s considered
-
Cole Gaither's profile was updated 2 years, 6 months ago
-
Paul Bruk started the topic Curtis Fuel Valves in the forum Airframe – Meyers 200 2 years, 6 months ago
Just replaced my fuel valves. I have a B model and my inboard tanks were 1/4 NPT. If your valves take a 9/16 wrench, it is the Curtis 1300 or 1600.
-
Mark Young wrote a new post 2 years, 6 months ago
I’m going to try to catch up on the name tags again at the fly-in.
If you’re coming to the fly-in and you lost or don’t have a nametag, send me an email to mark.young@gmail.com.
Heck, if you’d like a
- Load More
